REPLACEMENT JACUZZI SPA CIRCUIT BOARD- 2 PUMP with CIRC PUMP -J-300 LCD-LED SERIES- 2014-2015 -DOMESTIC/EXPORT (50/60 HZ) Models Covered Jacuzzi® circuit board 2014+ J-385, J-375, J-365, J-355, J-345, J-335 Replaces 6600-293 and 6600-364 Circuit Board supports 2014+ J-300 models with the CLEARRAY® on-demand function only. Introduction Welcome to this guide on how to replace the Jacuzzi® spa circuit board for 2 pump J-300 LCD-LED series, specifically for the 2014-2015 domestic and export models with a frequency of 50/60 Hz. This guide will walk you through the process of replacing your old circuit board with a new one, ensuring that your Jacuzzi® spa continues to function smoothly. About the Jacuzzi® Circuit Board The circuit board is a crucial component of any electronic device, including your Jacuzzi® spa. It serves as the brain of your spa, controlling and coordinating all its functions. The circuit board receives signals from various sensors and switches, interprets them, and sends out commands to other parts of the spa, such as pumps, lights, and heaters. Without a working circuit board, your spa would not be able to function properly. Signs of a Faulty Circuit Board There are several signs that may indicate an issue with your Jacuzzi® spa's circuit board. These include malfunctioning jets or pumps, failure to heat up, unresponsive controls or display screens, and error messages on the control panel. If you experience any of these issues, it may be time to replace your circuit board. Check Devices attached to the board and in particular the heater as they could be a cause of board failure and it is recommended to replace an old heater and the flow switch with the new board . Replacement Process Replacing a Jacuzzi® spa circuit board is a relatively straightforward process that can be completed in a few steps. Before beginning, make sure to turn off all power sources to the spa and disconnect it from its power supply. Once that is done, follow these steps: Remove the front panel of your spa to access the circuit board. Carefully disconnect all cables and wires from the old circuit board. Remove the old circuit board from its mounting position. Place the new circuit board in the same position as the old one and secure it in place. Check Programming jumpers that they are set for your options of tub Reconnect all cables and wires to the new circuit board. Replace the front panel of your spa. Turn on the power supply and test the new circuit board by running your spa's functions. If you are unsure about any step in this process, it is always best to consult a professional technician who is familiar with Jacuzzi® spas. Compatibility It is essential to ensure that the replacement circuit board is compatible with your specific Jacuzzi® spa model. This guide is specifically for 2 pump with Circ pump J-300 LCD-LED series models from 2014 to 2015, with a frequency of 50/60 Hz. Using an incompatible circuit board could result in further issues and may even damage your spa. Additional Tips Always follow proper safety precautions and turn off all power sources before attempting to replace the circuit board. Keep the new circuit board in its anti-static packaging until you are ready to use it. Carefully handle and install the new circuit board to avoid any damage. Regularly check and maintain your spa's components, including the circuit board, to prolong their lifespan and avoid future issues.

REPLACEMENT JACUZZI SPA CIRCUIT BOARD- 2 PUMP with CIRC PUMP -J-300 - 6600-297

Jaccuzzi
SKU:
W6600-297(MLH-2)
|
UPC:
6600-297
€472.50
(No reviews yet)
Width:
12.00 (in)
Height:
12.00 (in)
Depth:
1.00 (in)
Current Stock:
Adding to cart… The item has been added
Description

REPLACEMENT JACUZZI SPA CIRCUIT BOARD- 2 PUMP with CIRC PUMP -J-300 LCD-LED SERIES- 2014-2015 -DOMESTIC/EXPORT (50/60 HZ)

REPLACEMENT JACUZZI SPA CIRCUIT BOARD- 2 PUMP with CIRC PUMP -J-300 LCD-LED SERIES- 2014-2015 -DOMESTIC/EXPORT (50/60 HZ) Models Covered Jacuzzi® circuit board 2014+ J-385, J-375, J-365, J-355, J-345, J-335 Replaces 6600-293 and 6600-364 Circuit Board supports 2014+ J-300 models with the CLEARRAY® on-demand function only. Introduction Welcome to this guide on how to replace the Jacuzzi® spa circuit board for 2 pump J-300 LCD-LED series, specifically for the 2014-2015 domestic and export models with a frequency of 50/60 Hz. This guide will walk you through the process of replacing your old circuit board with a new one, ensuring that your Jacuzzi® spa continues to function smoothly. About the Jacuzzi® Circuit Board The circuit board is a crucial component of any electronic device, including your Jacuzzi® spa. It serves as the brain of your spa, controlling and coordinating all its functions. The circuit board receives signals from various sensors and switches, interprets them, and sends out commands to other parts of the spa, such as pumps, lights, and heaters. Without a working circuit board, your spa would not be able to function properly. Signs of a Faulty Circuit Board There are several signs that may indicate an issue with your Jacuzzi® spa's circuit board. These include malfunctioning jets or pumps, failure to heat up, unresponsive controls or display screens, and error messages on the control panel. If you experience any of these issues, it may be time to replace your circuit board. Check Devices attached to the board and in particular the heater as they could be a cause of board failure and it is recommended to replace an old heater and the flow switch with the new board . Replacement Process Replacing a Jacuzzi® spa circuit board is a relatively straightforward process that can be completed in a few steps. Before beginning, make sure to turn off all power sources to the spa and disconnect it from its power supply. Once that is done, follow these steps: Remove the front panel of your spa to access the circuit board. Carefully disconnect all cables and wires from the old circuit board. Remove the old circuit board from its mounting position. Place the new circuit board in the same position as the old one and secure it in place. Check Programming jumpers that they are set for your options of tub Reconnect all cables and wires to the new circuit board. Replace the front panel of your spa. Turn on the power supply and test the new circuit board by running your spa's functions. If you are unsure about any step in this process, it is always best to consult a professional technician who is familiar with Jacuzzi® spas. Compatibility It is essential to ensure that the replacement circuit board is compatible with your specific Jacuzzi® spa model. This guide is specifically for 2 pump with Circ pump J-300 LCD-LED series models from 2014 to 2015, with a frequency of 50/60 Hz. Using an incompatible circuit board could result in further issues and may even damage your spa. Additional Tips Always follow proper safety precautions and turn off all power sources before attempting to replace the circuit board. Keep the new circuit board in its anti-static packaging until you are ready to use it. Carefully handle and install the new circuit board to avoid any damage. Regularly check and maintain your spa's components, including the circuit board, to prolong their lifespan and avoid future issues.

 

typical topside control used in conjunction with this board sold separately 

j-300-topside control   

 

 

Related parts and links:

Item Part number Description Buy Link
Topside Control 1 pump  JAC6600-713  topside control for 1 pump systems  Buy Link 
Topside Control 2 pump
  JAC6600-715 topside control for 2 pump systems  Buy Link
Main fuse for spa pak  JAC6760-120  main 30 amp box fuse Buy Link
Heater , Pump relays  JAC6660-104  board relay for heater or pumps Buy Link
circ , ozone, light relays    board relay for circ , zone , light Buy Link
Transformer JAC2600-030  transformer for board Buy Link
F1 Location board fuse JAC6660-105  slow flow board fuse location f1 Buy Link

 

 

Models Covered

 

Jacuzzi® circuit board 2014+ J-385, J-375, J-365, J-355, J-345, J-335
Replaces 6600-293 and 6600-364

Circuit Board supports 2014+ J-300 models with the CLEARRAY® on-demand function only.

   j300-crosreference.gif

 

     U.S Domestic

    j300-crosreference2.gif

      EXPORT 

 crossreference-export.gif

 

Introduction

Welcome to this guide on how to replace the Jacuzzi® spa circuit board for 2 pump J-300 LCD-LED series, specifically for the 2014-2015 domestic and export models with a frequency of 50/60 Hz. This guide will walk you through the process of replacing your old circuit board with a new one, ensuring that your Jacuzzi® spa continues to function smoothly.

About the Jacuzzi® Circuit Board

The circuit board is a crucial component of any electronic device, including your Jacuzzi® spa. It serves as the brain of your spa, controlling and coordinating all its functions. The circuit board receives signals from various sensors and switches, interprets them, and sends out commands to other parts of the spa, such as pumps, lights, and heaters. Without a working circuit board, your spa would not be able to function properly.

Signs of a Faulty Circuit Board

There are several signs that may indicate an issue with your Jacuzzi® spa's circuit board. These include malfunctioning jets or pumps, failure to heat up, unresponsive controls or display screens, and error messages on the control panel. If you experience any of these issues, it may be time to replace your circuit board. Check Devices attached to the board and in particular the heater as they could be a cause of board failure and it is recommended to replace an old heater and the flow switch with the new board .

Replacement Process

Replacing a Jacuzzi® spa circuit board is a relatively straightforward process that can be completed in a few steps. Before beginning, make sure to turn off all power sources to the spa and disconnect it from its power supply. Once that is done, follow these steps:

  1. Remove the front panel of your spa to access the circuit board.
  2. Carefully disconnect all cables and wires from the old circuit board.
  3. Remove the old circuit board from its mounting position.
  4. Place the new circuit board in the same position as the old one and secure it in place.
  5. Check Programming jumpers that they are set for your options of tub
  6. Reconnect all cables and wires to the new circuit board.
  7. Replace the front panel of your spa.
  8. Turn on the power supply and test the new circuit board by running your spa's functions.

If you are unsure about any step in this process, it is always best to consult a professional technician who is familiar with Jacuzzi® spas.

Compatibility

It is essential to ensure that the replacement circuit board is compatible with your specific Jacuzzi® spa model.

This guide is specifically for 2 pump with Circ pump J-300 LCD-LED series models from 2014 to 2015, with a frequency of 50/60 Hz.

Using an incompatible circuit board could result in further issues and may even damage your spa.

Additional Tips

  • Always follow proper safety precautions and turn off all power sources before attempting to replace the circuit board.
  • Keep the new circuit board in its anti-static packaging until you are ready to use it.
  • Carefully handle and install the new circuit board to avoid any damage.
  • Regularly check and maintain your spa's components, including the circuit board, to prolong their lifespan and avoid future issues.

 

 

 

Warranty
manufacturer warranty