DAZZLE Balance TA Hot Tub Spa ( Alkalinity increaser ) ( 750 gr )
$9.95
(No reviews yet)
Write a Review
DAZZLE Balance TA Hot Tub Spa ( Alkalinity increaser ) ( 750 gr )
DAZZLE Balance TA Hot Tub Spa ( Alkalinity increaser ) ( 750 gr )
What is Total Alkalinity?
Total Alkalinity (TA) is a very important component of overall water balance. Its primary role is to help keep pH in proper balance. The best definition of TA is; “the measure of water’s ability to resist a change in pH.” In other words, once you balance your pH successfully within the range of 7.4 – 7.6, it is TA that helps you keep it there. The secondary role of TA is to assist in providing the overall mineral content that all water requires to prevent unnecessary damage to surfaces. Water low in TA will see the pH bouncing up and down, almost uncontrollably. . Water high in TA will find the pH constantly high and in need of reducing and a greater risk of scale formation, cloudy water and shorter filter runs.
Ideal TA Levels: All Hot Tub Surfaces: 125 – 150 ppm
Reducing Total Alkalinity:
When TA is high, it requires lowering with Dazzle Pro Balance pH- or Dazzle Acid Enhance, a safe, dry form of acid. Lowering TA is traditionally done over a number of days to slowly and safely lower the TA without reducing the pH to dangerously low levels. When done properly, the TA slowly steps down and the pH never drops below 7.2. Safe and Simple!
Steps:
-
Test pH – if above 7.2, apply that days application of Pro Balance pH-.
-
If below 7.2, wait for the pH to climb above 7.2 before making your next application. It will come up on its own.
-
Apply by broadcasting evenly over the water surface, primarily in the deep end.
-
Make note of the application to ensure you complete the number of applications required.
To Speed Up the Process:
-
Test pH – if above 7.2, apply that days application of Pro Balance pH-.
-
After 1 – 2 hours, test pH again. If the pH is still above 7.2, apply another application of Pro Balance pH-.
-
Repeat this process every 1 – 2 hours, making applications of Pro Balance pH- provided the pH remains above 7.2. This process allows for many applications to be made per day, provided the pH remains above 7.2.
-
Stop applications once the pH drops below 7.2, restarting once the pH climbs above 7.2 again.
-
Make note of each application and stop once the total number of applications have been made
Hot Tub Maintenance Checklist
Start-Up
-
While hot tub is filling, add initial dose (375 ml per 1,000 L) of DazzleTM
-
Stain & Scale 1 to cold water. Once full, start pump, operate with the aeration off and commence heating.
-
Bring a water sample to your DazzleTM Retailer for water balance recommendations.
-
Balance water according to your DazzleTM Retailer’s recommendations.
-
Allow water to circulate for 2 hours.
-
Apply DazzleTM Amaze per label directions (2 caps per 1,000 L). Ensure that the pump and filter are operating and leave the cover off for a minimum of one hour after application. Allow water to circulate for at least 15 minutes before proceeding to next step.
-
Add initial dose of DazzleTM Botanical Cleanse (3 caps per 1,000 L). Pour around the edges of the hot tub with the pump operating and the aeration off.
-
Avoid adding DazzleTM Botanical Cleanse when the sanitizer level is above 5 ppm.
-
Apply chlorine or bromine to the hot tub. Use DazzleTM Bromine Granules or Chlorine Granules to initially establish the residual. Fill your tablet dispenser with enough DazzleTM Bromine Tablets or Mini Chlorinating Tablets to maintain a continuous level of 3.0 – 5.0 ppm through the week.
-
Add initial dosage of DazzleTM Performance Plus (200 g per 1,000 L). Apply through the skimmer or in front of the suction plate with the pump in operation and the aeration off.
-
Add initial dosage of DazzleTM Nature Sheen (20 ml per 1,000 L.). Apply with the pump in operation and the aeration off. Run filter continuously until water clears. DazzleTM Nature Sheen will agglomerate particulate into masses large enough to be filtered out. Watch filter closely and clean as required.
As Required
Test sanitizer and pH level with DazzleTM Test Strips. Add DazzleTM Bromine Granules or Chlorine Granules to boost the sanitizer level should it fall below 3.0 ppm. Always maintain the bromine/chlorine reading between 3.0 – 5.0 ppm. The pH level should be maintained at 7.4 – 7.6.
Weekly
-
Add regular weekly dosage of DazzleTM Stain & Scale 2 (1 cap per 1,000 L) to protect against metal staining and scale formation.
-
Oxidize water with DazzleTM Amaze (2 caps per 1,000 L) by broadcasting over water surface. Note: heavy bather load may require more frequent applications. Allow water to circulate for at least 15minutes and leave the cover off for minimum 1 hour. Wait 15 minutes before moving to next step.
-
Digest and remove organics with DazzleTM Botanical Cleanse (3 caps per 1,000 L).
-
Re-fill your tablet dispenser with enough DazzleTM Bromine Tablets or Mini Chlorinating Tablets to maintain a continuous level of 3.0 – 5.0 ppm through the week.
Add weekly dosage of:
DazzleTM Performance Plus (6½ caps per 1,000 L).
DazzleTM Nature Sheen (½ cap per 1,000 L).
-
Brush, skim and vacuum. Remove filter cartridge and rinse with water from garden hose.
-
Clean water line with DazzleTM Tub Cleanse, if necessary.
Monthly
-
Have water tested at your DazzleTM Retailer. Adjust pH, total alkalinity, calcium hardness as required.
-
Clean cartridge with DazzleTM Filter Cleanse as per label directions.
Draining
-
Clean entire hot tub including plumbing lines with DazzleTM Drain Prep. Add as per label directions the day before draining.
-
Drain hot tub and clean surfaces with DazzleTM Tub Cleanse.
-
Clean cartridge with DazzleTM Filter Cleanse as per label directions.
-
Clean cover with DazzleTM Cover Cleanse & Protect as per label directions.
